| Items |
 3004 Polyurethane Gloss Varnish |
 E15712 / E15713 100% Solids Clear Epoxy Two Component |
||
| Description | Warren's Polyurethane Gloss Varnish is formulated to withstand the mild chemical exposure and abrasion. Polyurethane Gloss Varnish is ideal for brush, roller, or spray application due to its moderate dry times. It fully cures overnight and is recommended for application to interior wood, concrete, and properly primmed steel surfaces. Polyurethane Gloss Varnish is available by special order in a wide range of colors and degrees of gloss, and provides good chemical and abrasion resistance. | Warren's 100% Solids Clear Epoxy is formulated to provide extreme resistance to water, alcohol, and other chemicals. It may be used in aggressive environments for long-term protection of steel and concrete. 100% Solids Clear Epoxy is well suited for decoupage on bar tops, table tops, or as a clear finish over other interior wood and concrete surfaces. It may be applied up to 1/4" per pour for a coating with tremendous "depth." 100% Solids Clear Epoxy should not be used as an exterior topcoat. | ||
| Features |
High Gloss Chemical and Abrasion Resistant Ideal for Interior Wood, Metal, and Concrete |
Cures Crystal Clear Cures Without Shrinkage Excellent Chemical Resistance and Hardness |
||
| Surface Preparation | Remove all dirt, scale, grease, and wax. Prep uncoated wood surfaces with Warren's sanding sealer. | Remove all dirt, scale, and grease. Remove wax and any other coatings. Allow to dry thoroughly. | ||
| Mixing and Thinning | Stir or shake well. Thin up to 33% with S 46, Spraying Thinner; S 3, VM&P Naphtha; or another recommended thinner to spray. Use as supplied or thin sparingly with S 4, Deodorized Thinner to brush or roll. Do not over-thin. | Mix two parts by volume of E15712 (part A) to one part of E15713 (part B) with gentle mechanical agitation for two minutes. Avoid entraining air into mixture. | ||
| Warning | Mixture will exotherm within 15 minutes of mixing, producing intense heat and fumes if not quickly spread over the surface to be coated. Mix only what can be spread in 15 minutes! If exotherm occurs, vacate the area and provide copious ventilation. Part B and any mixture thereof is slightly corrosive. Wear gloves and goggles. Wash exposed skin with soap and water. Flush eye contamination with water for 15 minutes and seek medical attention. | |||
| Application | Brush, roll, spray. Thin as directed for conventional or H.V.L.P. spray. Apply between 50 and 95ºF with the relative humidity less than 80%. Do not expose to dew or rain within eight hours after painting. | Apply by pouring, brushing, troweling, or by squeegee. Rolling may entrain air bubbles. Apply to a maximum thickness of 1/4" to avoid intense exotherm. Apply in multiple coats for thicker finishes. To release air bubbles, direct hot air onto the freshly applied coating, i.e. hair dryer. Full properties are developed within seven days. Apply between 60ºF and 90ºF and less than 80% relative humidity. | ||
| Dry Time | 1-1/2 hours to touch. Eight hours to handle. Twenty-four hours hard. | Eight hours to touch. 24 hours for light foot traffic. Seven days for full resistance properties. | ||
| Recoat Time | Before one hour and after eight hours. | Recoat after eight hours, or as soon as tack free. After 48 hours, a light sanding with aluminum oxide, 400 grit sandpaper followed by a fresh water rinse is recommended before recoat. | ||
| Appearance | High gloss mirror-like clear film. | High gloss crystal clear film. | ||
| Composition | None | |||
| Vehicle | Oil-modified Aromatic polyurethane reduced with mineral spirits. | Epoxy and cycloaliphatic amine. | ||
| % Solids by Weight | 50.0 | 100 | ||
| % Solids by Volume | 41.6 | 100 | ||
| Coverage | 418 square feet per gallon at 1.6 mils DFT (100% transfer and zero profile). | 13 square feet per gallon at 1/8" DFT; 320 square feet per gallon at 5 mils DFT | ||
| V.O.C. | 3.75 lb/gal | 0.0 lb/gal as supplied | ||
| Cured Film Properties | Good water and chemical resistance within twenty-four hours. Good resistance to aliphatic solvents and many oils within seven days. Excellent abrasion resistance. | Excellent anticorrosive properties over steel. Very good water resistance within eight hours. Good resistance to solvents and chemicals within seven days. Not designed as an exterior finish coat. | ||
| Standard Packaging | One gallon cans (packaged four per case). Fives and drums are available by special order | Three gallon kit. | ||
|
|
||||
